Free delivery to the UK and US · Printed to order

How to light a framed print: picture lights explained

A picture light is a small lamp fixed above a frame that washes the print in warm light. The easiest kind for a rented or finished room is a rechargeable battery one with a remote, because it needs no wiring and no drilling into the wall.

The print from this post.

Looking for a gift? Christmas gifts for him, her, dad and mum.

Edgar Allan Poe The Raven art print in the style of a 19th-century lithograph: a black raven perched on a pale marble bust above a scholar's door at midnight, a single candle flame the only colour, with Quoth the Raven, Nevermore typeset in the white border below. Shown framed in black, white and natural oak and unframed, A4 and A3.

Some links on this page are affiliate links.

A print you love deserves to be seen after dark. A ceiling light flattens a room and leaves the walls in shadow, so a framed print that looks rich at noon can disappear by eight o'clock. A picture light fixes that: one small lamp, aimed at one picture, and the print becomes the brightest thing in the room.

Battery, plug-in or hardwired

There are three ways to power a picture light, and the right one depends on how settled the wall is.

  • Battery (rechargeable): no cable and no electrician. Most charge by USB and come with a remote and a timer. The trade-off is charging every few weeks, depending on how long you leave it on.
  • Plug-in: a thin cable runs down the wall to a socket. Bright and always ready, but you will see the cable unless you paint it or run it behind furniture.
  • Hardwired: the cleanest look, with the wire hidden in the wall, but it needs an electrician and suits a wall you are not going to change.

For a rented flat, a new build you do not want to mark, or a print you might move to another room next year, battery is the sensible choice. Many fix with a small screw or a strong adhesive pad, and some hang from the top of the frame itself.

Buy these prints

Where to fix it

Fix the light centred above the frame, about 15 to 20cm above the top edge, with the head angled down so the beam falls across the whole picture rather than a bright patch at the top. A light roughly half to two thirds the width of the frame gives an even spread. On a wide landscape print, choose a longer bar light rather than a small round one.

If the print is behind glass, a light fixed too close and too steep will bounce straight back at you as glare. Tilt the head a little further forward, or move it slightly higher, until the reflection drops out of your eye line. Our frames use plexiglass, which is lighter than glass and a little less reflective, but the same rule applies.

Nevermore: Natural oak frame, A3, leaning in a bedroom, full bleed
Nevermore, natural oak frame, A3, leaning in a bedroom, full bleed

Warm white or cool white

Choose warm white, around 2700 to 3000K. It is the colour of an old reading lamp, and it flatters cream paper, ink, watercolour washes and the soft blacks of an engraving. Cool white, 4000K and above, makes a white border look blue and a warm sunset look tired. If the light lets you change colour temperature, set it to the warmest setting and leave it there.

Brightness matters less than you think. A picture light is there to lift the print a little above the rest of the room, not to floodlight it, so a dimmable light set to half is usually right in the evening.

Lighting dark prints

Night scenes gain the most from a picture light. A dark print in a dim room can read as a black rectangle, but light it and the detail comes forward: the candle in the window, the moonlight on the water, the lamplit street. Our Nevermore and Hogwarts by Night were made for exactly this.

Dark, atmospheric prints look best lit. Browse our night scenes: prints by style.

Want it lit? A battery picture light sits above the frame with no wiring, and comes with a remote: this antique brass one on Amazon › (As an Amazon Associate, Chapter & Scene earns from qualifying purchases.)

Hogwarts by Night: Natural oak frame, A3, leaning against a terracotta wall, full bleed
Hogwarts by Night, natural oak frame, A3, leaning against a terracotta wall, full bleed

A quick checklist

  1. Measure the frame, and choose a light about half to two thirds its width.
  2. Pick warm white, 2700 to 3000K, and a dimmer if you can.
  3. Centre it 15 to 20cm above the frame and angle it down.
  4. Check for glare from where you sit, and tilt until it goes.
  5. Set a timer, so it comes on as the evening does.

More guides

Next, read how to hang a print without drilling, or how to hang a gallery wall of book prints. Not sure which size fits your wall? Try our print size picker.

Related reading: which print size to buy and dark academia wall art.

Questions

Can I use a picture light without a plug?
Yes, rechargeable battery ones exist with a remote.
Will a picture light damage my print?
Warm LED light gives off almost no heat or UV, so it is safe for a framed print.
How far above the frame should a picture light go?
About 15 to 20cm above the top of the frame, angled down so the light covers the whole picture.
Shop the post

Prints in this post

Related posts

A free digital print when you join

Be first to see new prints

Join and get a free digital print (wallpapers and printable files), then emails about new prints and the occasional offer. Unsubscribe any time. Privacy.

Find us elsewhere